The short answer
Gather the Right Materials
You will need sheets of plywood, at least half an inch thick. The wood should be pressure-treated to resist moisture. Have a measuring tape, a saw, and a drill ready. You also need long exterior-grade wood screws, at least two and a half inches long, and washers to help distribute the pressure and create a tight seal against the frame.
Purchase your materials well before a storm is forecast. Stores often sell out of plywood quickly. If you live in Akron, keep storm supplies on hand during the season. Having everything ready saves crucial time. You can pre-cut plywood for your windows and label each piece for easier, faster installation when a warning is issued.
Measure and Cut the Plywood
Measure the height and width of your window from the outside trim. Add a few extra inches on each side for secure coverage. Your plywood should completely cover the window frame and overlap onto the surrounding wall. This overlap ensures the board anchors into solid wood, not just the window casing, which may be weaker.
Transfer your measurements to the plywood sheet and mark the cutting lines clearly. Use a circular saw for straight, clean cuts. Always wear safety glasses and gloves when cutting. Double-check each piece fits its designated window before you begin the installation process. Pre-cutting and labeling pieces in advance makes the job much faster during an emergency.
- Cover the entire window opening and frame.
- Overlap the surrounding wall by at least two inches.
- Use pressure-treated plywood for moisture resistance.
- Label each board with the window's location.
- Store pre-cut boards in a dry, accessible place.
- Wear safety gear like glasses and gloves.
Secure the Boards Properly
Position the plywood over the window from the outside. Have a helper hold it steady. Drill pilot holes through the plywood and into the window frame or, better yet, the wall studs surrounding the window. Using a drill prevents the wood from splitting and ensures a stronger hold. Space your screws about 12 to 16 inches apart along the edges.
Drive long screws with washers through the pilot holes. The washers help keep the screw heads from pulling through the plywood under high wind pressure. Tighten the screws firmly to create a weather-tight seal. Do not use nails, as wind can pry them loose. Check each screw is secure before moving to the next window.
Prioritize Safety During Installation
Never board up windows from the inside. Wind pressure can push the entire window, glass, and frame inward. The board must be on the exterior to absorb the force. Work with a helper, especially when handling large sheets of plywood on a ladder. Always ensure your ladder is on stable, level ground before climbing.
Wear sturdy shoes, gloves, and eye protection. Be aware of overhead power lines when moving long boards. If a storm is imminent and you cannot safely finish, prioritize getting to a secure location. Do not risk injury. A broken window can be repaired, but personal safety is the most important consideration during severe weather preparation.
What If Water Gets in Anyway
Despite boarding, wind-driven rain can sometimes find a way inside. If water enters your home, act quickly to minimize damage. Remove as much water as possible with a wet-dry vacuum or mops. Move furniture and rugs away from the area. Promote air circulation by opening interior doors and using fans, if it is safe to do so.
For significant flooding, local water damage pros can help. They have industrial equipment to extract water and dry the structure thoroughly. Lingering moisture leads to mold and structural rot. If you live in Akron's humid continental climate, fast drying is critical. Policies vary, and your insurer decides what is covered. You may need services like water-damaged flooring removal or drywall water damage repair.
- Extract standing water immediately.
- Move belongings to a dry area.
- Use fans and dehumidifiers to circulate air.
- Inspect for hidden moisture in walls.
- Contact a plumber if a pipe broke.
- Document all damage for insurance.
Need help right now?
Phones are answered 24/7 for Akron and nearby communities.
Call Now (330) 632-1753Frequently asked questions
What thickness of plywood should I use?
Use at least half-inch thick, exterior-grade plywood. For larger windows or in areas expecting very high winds, five-eighths inch plywood provides better strength. Thinner materials can crack or be punctured by flying debris. The goal is to create a solid barrier that can withstand impact and pressure.
Can I use nails instead of screws?
No, you should not use nails. Screws have much greater holding power and are less likely to be pulled out by cyclonic wind forces. Always use long, exterior-grade wood screws with washers. This creates a secure, lasting hold that nails cannot provide in a storm situation.
Should I board up every window in my house?
Prioritize windows facing the prevailing wind direction and large picture windows. Ground-floor windows are most vulnerable. If time is short, secure the most exposed windows first. Boarding all windows offers the best protection, but any secured window reduces the risk of catastrophic glass breakage and water intrusion.